Recent posts
#71
Out of Production Hardware / Re: Huntron Protrack I - It r...
Last post by admin - November 06, 2023, 08:57:59 AMQuote from: ealonso on November 06, 2023, 06:27:03 AMHi everyoneThanks for the update.
After the capacitors replace and a few days of use, it seems that the problem has desapeared.
Thank you so much.
#72
Out of Production Hardware / Re: Huntron Protrack I - It r...
Last post by ealonso - November 06, 2023, 06:27:03 AMHi everyone
After the capacitors replace and a few days of use, it seems that the problem has desapeared.
Thank you so much.
After the capacitors replace and a few days of use, it seems that the problem has desapeared.
Thank you so much.
#73
Obsolete Software / Re: Huntron ProTrack I + Scann...
Last post by admin - November 06, 2023, 06:21:08 AMThe Product manuals CD Part Number: 06-5217
You would need to order through your local distributor.
You would need to order through your local distributor.
#74
Obsolete Software / Re: Workstation 3.5.4 sigAssis...
Last post by admin - November 06, 2023, 06:18:02 AMSigAssist can be useful on some occasions but it is the signature analysis that is more important. It was in its infancy with version 3. The value calculations are much better in version 4.
#75
Obsolete Software / Re: Workstation 3.5.4 sigAssis...
Last post by Al1234 - November 05, 2023, 06:13:30 AMThank you fetron, I got some reading in that window.
#76
Out of Production Hardware / Re: Protrack I 20 over voltage...
Last post by Al1234 - November 05, 2023, 06:11:33 AMThank you. Yesterday these guys where throughing over voltage without being used and also during use.
I didn't know protrack can charge caps in boards to the point of causing a fault. Thanks.
I just noticed the 2nd or 3rd time I went over a 14 pin chip in circuit protrack faulted out "over voltage".
About faulting "over voltage" when not in use, Last night and today left the protracks on for an hour at a time. No fault.
If it's an external signal causing this, Maybe has something to do with the time of day. I will try it the same time in the next couple of days and report back.
I didn't know protrack can charge caps in boards to the point of causing a fault. Thanks.
I just noticed the 2nd or 3rd time I went over a 14 pin chip in circuit protrack faulted out "over voltage".
About faulting "over voltage" when not in use, Last night and today left the protracks on for an hour at a time. No fault.
If it's an external signal causing this, Maybe has something to do with the time of day. I will try it the same time in the next couple of days and report back.
#77
Out of Production Hardware / Re: Protrack I 20 over voltage...
Last post by jvthorsley - November 04, 2023, 04:58:02 PMOn a KJ2 "Over Voltage" usually comes up when an over voltage has been applied to the input.
Or even when a higher voltage range on the ProTrack has charged a Capacitor in the circuit can cause this.
Or even when a higher voltage range on the ProTrack has charged a Capacitor in the circuit can cause this.
#78
Out of Production Hardware / Protrack I 20 over voltage
Last post by Al1234 - November 04, 2023, 12:17:23 PMAnyone knows why a protrack throughs error "over voltage" saying press channel A or B. But has to be turned off/on to resume operation again.
There are 2 that are doing this at random but otherwise they work fine it seems..
They are not being used when error happens. But leads are connected to the protrack. Sometimes the unit is on And is working Then I leave the desk for some reason when I come back the error is on the screen.
1 kj3 and the other kj4.
There are 2 that are doing this at random but otherwise they work fine it seems..
They are not being used when error happens. But leads are connected to the protrack. Sometimes the unit is on And is working Then I leave the desk for some reason when I come back the error is on the screen.
1 kj3 and the other kj4.
#79
Obsolete Software / Re: Workstation 3.5.4 sigAssis...
Last post by fetron - November 03, 2023, 11:29:42 AMCreate a troublesheet.
Then take measurements on several pins and save the measurements.
Then open the saved measurements and go to the View Signature Zoom window.
Here you have to press the Hardware connect button.
Drag the mouse over the signatures and you can measure with the help of SigAssist.
Now you can change pins and ranges.
Drag the mouse over the signatures and you can measure with the help of SigAssist.
Workstation 4 manual in pdf attachment.
Then take measurements on several pins and save the measurements.
Then open the saved measurements and go to the View Signature Zoom window.
Here you have to press the Hardware connect button.
Drag the mouse over the signatures and you can measure with the help of SigAssist.
Now you can change pins and ranges.
Drag the mouse over the signatures and you can measure with the help of SigAssist.
Workstation 4 manual in pdf attachment.
#80
Obsolete Software / Re: Workstation 3.5.4 sigAssis...
Last post by Al1234 - November 03, 2023, 09:52:41 AMOn both kj3 and kj4 no capacitor measurements in veiw signature zoom window as well. Diode and resistance measurement are crappy and spotty.
And there is no way of changing the range there.
In view signature zoom window, If I choose hardware / connect / manual then it goes in manual mode where range can be changed. But then measured signature in the manual mode can't be linked to the view signature zoom window. And still sigAssist is no no 😪😓😭
And there is no way of changing the range there.
In view signature zoom window, If I choose hardware / connect / manual then it goes in manual mode where range can be changed. But then measured signature in the manual mode can't be linked to the view signature zoom window. And still sigAssist is no no 😪😓😭