#21

Out of Production Hardware / Re: Huntron Tracker 2500 Manua...

Last post by admin - January 18, 2024, 02:45:42 PM

Okay thank you for the help.

Ljcttech, were you able to fix the problem on your Tracker 2500? If yes, can you share the solution?
Thanks!

#22

Current Hardware - Tracker 3200S, Tracker 2800/2800S and Access Probers / Re: Access 2 camera

Last post by admin - January 02, 2024, 01:48:27 PM

I recall seeing this Prober on EBay. It is pretty old. Can you post an image of the area on the Z head where the camera would be mounted? I want to verify the camera connection that would have been used (NTSC or USB).

If it is USB then Imaging Source still sells lists the correct camera.
https://www.theimagingsource.com/en-us/product/industrial/2u/dmk42auc03/

You will also need to purchase a Workstation license.

#23

Current Hardware - Tracker 3200S, Tracker 2800/2800S and Access Probers / Re: Access 2 camera

Last post by TechnikaSystem - January 02, 2024, 01:16:48 PM

Yes Z.
Serial 550-01021. Will the DFK 72BUC02 be good?

#24

Current Hardware - Tracker 3200S, Tracker 2800/2800S and Access Probers / Re: Access 2 camera

Last post by admin - January 02, 2024, 12:53:18 PM

Welcome to the Huntron Users Forum, TechnikaSystem.

Is the USB cable that would go to the camera on the Z head still in place? If it is an older Prober it may have a power cable and BNC for the camera instead. Can you supply a serial number?

The DFK camera model we use is 42AUC03 with a C mount lens.

#25

Current Hardware - Tracker 3200S, Tracker 2800/2800S and Access Probers / Access 2 camera

Last post by TechnikaSystem - January 02, 2024, 10:14:18 AM

Hello. I bought a second-hand Huntron Access 2, unfortunately, it does not have the main camera. What type of DFK camera and lens should I use for it to be correct? Thank you in advance for the information.

#26

Out of Production Hardware / Re: Huntron Tracker 2500 Manua...

Last post by Ljcttech - December 28, 2023, 03:06:50 PM

Okay thank you for the help.

#27

Out of Production Hardware / Re: Huntron Tracker 2500 Manua...

Last post by admin - December 27, 2023, 06:25:32 AM

The power supply section is on the main pcb. The schematics are linked earlier in this thread. As JVTHorsley suggests, check all of the caps and diodes that go to ground and the regulators U11 and U12.

#28

Out of Production Hardware / Re: Huntron Tracker 2500 Manua...

Last post by jvthorsley - December 23, 2023, 08:30:55 AM

Hi
Is the PSU a separate unit on the 2500.
If so does the fuse still blow with PSU isolated from the logic circuit board.
Blowing fuses normally caused when large capacitors or Diodes fail on the bridge rectifier section on the mains input.

#29

Out of Production Hardware / Re: Huntron Tracker 2500 Manua...

Last post by Ljcttech - December 22, 2023, 09:12:31 PM

I have problems my huntron 2500 keep blowing fuse.  Any tips be helpful. 

#30

Out of Production Hardware / Re: Protrack KJ2 EEPROM

Last post by fetron - December 21, 2023, 01:22:41 AM

Dear Admin!

The firmware number 06-5098 that you uploaded on December 14 belongs to the KJ4.

Firmware 06-5069 is for the KJ2 (which Ken needs).
Can you upload this?